Post by faramirsmumma on Nov 18, 2005 17:14:13 GMT -5
"Greenstuff" Gav
This is guide after a random conversation with TinFish, hence it's hap-hazardness.. I made it up as I went along!
Firstly, find something flat that you can move about & dont mind putting Greenstuff onto (I'm using the plastic insert the Balrog comes in, but a blister pack would suffice).
theholyart.co.uk/images/laurels_01.jpg
Next, apply some moisture to the top of the pack.
I use water dapped from a damp sponge, but some people use oils.
The purpose is to stop the greenstuff sticking to the pack. This takes a bit of practise, several times I had to start again as the greenstuff had stuck to the pack...
Place a piece of greenstuff about the right size for the laurel on the pack.
Use a modelling tool to even out the thickness and smoothen out any fingerprints.
theholyart.co.uk/images/laurels_02.jpg
Once you have an even height of greenstuff, use a fine knife to cut off the edges to get an even rectangle.
theholyart.co.uk/images/laurels_03.jpg
After cutting each edge, use the flat of the blade to make sure the Greenstuff hasn't stuck to the packet.
theholyart.co.uk/images/laurels_04.jpg
After getting a nice clean, even shape, take a sharp modelling knife & score a line down the centre of the greenstuff gently.
Then check the Greenstuff is still moveable & not stuck to the work surface
theholyart.co.uk/images/laurels_05.jpg
Now Very Very Carefully, cut the corners off the end at about 45 degrees.
theholyart.co.uk/images/laurels_06.jpg
Now run slightly deeper marks at 45degree angle all along both sides of the line.
Take your time & try to get the lines even They need to be deep enough that they are not obscured by the undercoat, but not actually cutting all the way through the greenstuff.
theholyart.co.uk/images/laurels_07.jpg
Then check the Greenstuff is still moveable.. spot a pattern here?
Next, mark & cut off a triangle along the other end, try to keep it central!
Then check the Greenstuff is still moveable...
theholyart.co.uk/images/laurels_08.jpg
![]()
theholyart.co.uk/images/tn_laurels_08.jpg" border="0"></a><a href="images/laurels_09.jpg[/img]
![]()
theholyart.co.uk/images/tn_laurels_09.jpg[/img]
Finally, leave for an hour or so for the greenstuff to start to start to harden (but still flexible enough to place on the fig!)
Carefully peel it off the pack and position on the figure. It's generally best to place the pointed end, then wrap the laurel around, then cut off any excess on the other end.
Repeat all these steps for the otherside, leave to dry overnight
This takes alot of practice to get right (from not sticking the laurel to the lid to lifting it without tearing it...) , but it certainly worth the effort!
Ed Note Thanks again Gav, this article is (in my opinion) one of your best! I know that my Imperial Fists shall be getting some of these
This is guide after a random conversation with TinFish, hence it's hap-hazardness.. I made it up as I went along!
Firstly, find something flat that you can move about & dont mind putting Greenstuff onto (I'm using the plastic insert the Balrog comes in, but a blister pack would suffice).
theholyart.co.uk/images/laurels_01.jpg
Next, apply some moisture to the top of the pack.
I use water dapped from a damp sponge, but some people use oils.
The purpose is to stop the greenstuff sticking to the pack. This takes a bit of practise, several times I had to start again as the greenstuff had stuck to the pack...
Place a piece of greenstuff about the right size for the laurel on the pack.
Use a modelling tool to even out the thickness and smoothen out any fingerprints.
theholyart.co.uk/images/laurels_02.jpg
Once you have an even height of greenstuff, use a fine knife to cut off the edges to get an even rectangle.
theholyart.co.uk/images/laurels_03.jpg
After cutting each edge, use the flat of the blade to make sure the Greenstuff hasn't stuck to the packet.
theholyart.co.uk/images/laurels_04.jpg
After getting a nice clean, even shape, take a sharp modelling knife & score a line down the centre of the greenstuff gently.
Then check the Greenstuff is still moveable & not stuck to the work surface
theholyart.co.uk/images/laurels_05.jpg
Now Very Very Carefully, cut the corners off the end at about 45 degrees.
theholyart.co.uk/images/laurels_06.jpg
Now run slightly deeper marks at 45degree angle all along both sides of the line.
Take your time & try to get the lines even
They need to be deep enough that they are not obscured by the undercoat, but not actually cutting all the way through the greenstuff.theholyart.co.uk/images/laurels_07.jpg
Then check the Greenstuff is still moveable.. spot a pattern here?
Next, mark & cut off a triangle along the other end, try to keep it central!
Then check the Greenstuff is still moveable...
theholyart.co.uk/images/laurels_08.jpg
theholyart.co.uk/images/tn_laurels_09.jpg[/img]
Finally, leave for an hour or so for the greenstuff to start to start to harden (but still flexible enough to place on the fig!)
Carefully peel it off the pack and position on the figure. It's generally best to place the pointed end, then wrap the laurel around, then cut off any excess on the other end.
Repeat all these steps for the otherside, leave to dry overnight
This takes alot of practice to get right (from not sticking the laurel to the lid to lifting it without tearing it...) , but it certainly worth the effort!
Ed Note Thanks again Gav, this article is (in my opinion) one of your best! I know that my Imperial Fists shall be getting some of these
